Видео

Great informative video as always!

I just hate leak searching...

Great podcast Gary. Thank you two for the knowledge.

Never knew what the gas ballast's purpose was until I saw your helpful video. I've been working with high-powered 16kW Leybold screw vaccuum pumps for a couple of years and always wondered what that gas ballast is for. For servicing, we always had to change the air filter once a year, and boy, do they clog up a lot of grime.

Great video 😊

Why a contractor should be replaced with a compressor?

Great video 👍

The “yep” count was out of control on this one 😂

this is a creative way to do this, thanks

Good info here to avoid premature compressor failure

Does this work with the old economizer actuator

wont air get in the lines tho??

pls help, how do i know which ac hard start kit for my residential ac lennox 5 ton

I'm here because I saw you write this on ig 😂

You forgot to put the flare nut on first, ROOKIE!

The unastrut sticking through the middle of the van is very relatable

Man, I'm watching this 5 years later and cringing at my video skills back then 😂

Finally found a mechani. Can't explaining the valve function. Function just one. Thank you when you start from city one turn. The term is cracked to the port. Thank you for the video

Great video. Thank you for sharing

Awesome thanks for sharing your knowledge

Excellent troubleshooting tech

lol this is basic hvac 101

👍

Thanks for the video

Great job 🎉

This man is amazing always great

Excellent video. Clear, simple, & Straight to the point. THANK YOU!

Turn your phone HORIZONTAL .... Vertical videos SUCK .... that's why I don't watch SHORTS at all!

HVAC methodical troubleshooting

Very useful information, I was searching for it.

on my vacuum pump , it has what is labeled as a blanking valve . is this what is considered the gas ballast valve ??

Come on man dont wax philosophical about a squirrel cage Im busy😂

What would the result/symptoms be if the solenoid were to get stuck in the open(unloading) position? Would pressures equalize?

Make this is EXCELLENT EXPLANATION!!! Wgreat video

can i use this for lifting things on roofs just extend the rope

Man you are a hero. I have watched over 20 videos on how heat pump works, I was so confused, like fucking water actually mix with refrigerant? Like wtf, nobody mentioned or explained the coaxial coil and how it works. Thanks god I found your video

Thanks bro!

Just what I needed! I was wondering why no freon was going in.... Turns out I have no idea what I'm doing. But now I kinda do!

I stared my hvac business in Canada 12 years ago. I’ve always just wanted a balanced work life. I knew very little about business and hard to learn thru a lot of bumps. I was tired of working for somebody, counting on the weather to keep us busy. It’s so hard to get ahead in business, especially with the crazy economy. Here it’s hard to sell a 3 ton a/c system for 5000$. I see guys in the states that wouldn’t touch it for less than 10-15k. Business stresses me out. I’m tired of the rollercoaster and catch up game that always seems to be going on. Sometimes I wish I never got into this. There is a few perks for sure , but sometimes I just wish I stayed working for the man

Nice thank you I'm getting 15.7 across all three leg start run and common. It was a little hot but all three legs are Reading the same so it is not grounded or in thermal lockout. But when the 24 volts are engaged the compressor stays at 290 on the low side and high side it is not adjusting in any way.

Any review on the pocket version I think it’s the pocket 2

Usually one of the worst issues these units have that is always not addressed at the factory is bad soft foot from those formed bases. I routinely see 0.020-0.050” soft foot.

Found one like that on a carrier today tripping the breaker

can you cut steel with that rig? Also, when brazing, do you have the option of using just MAPP or do you have to use O2 all the time?

Geat video. I know you did not flow nitro for demonstration purposes, what is the best way to remove those flakes from that txv afterwards?

Boring mtfkr

How much was the set, an estimate since it was last year. And how much is each tank? 🤔✌🏾 I’ll plan ahead, thanks in advance.

the whole static pressure is a shit fools gimic to make more money

Golf clubs? Lame.

Is it Boost spp6 would be efficient for 45+5 mdf capacitor? Thanks!